In this SOOC shot, you can see just how down and dirty this setup was. The backdrop is not pulled out very far and taped down only in a couple of spots. In the top left edge of the image you can see the corner of the 50 inch Apollo. This also shows that the right edge of the light is hitting the subject, allowing for a soft feathered look, but more importantly for this setup, it's allowing the rest of the box to light our background.
I love this backdrop for photos; I used it for my daughters pictures to use on her first birthday card. However, as other reviewers stated, getting the creases out is nearly impossible. I took another persons idea of wrapping it around a pole (one of those long, skinny paint rollers meant for painting ceilings - so very skinny). I wrapped it around the pole and used tape to hold it in place for TWO WEEKS. While it helped with the creases a little bit, they were still pretty visible. I would love to purchase more of these for future use but am hesitant; I wish the supplier would ship them rolled in tubes as opposed to folding them.
When I received this it was folded down to 1'x6" package. After unfolding it, every fold line is very visible. Also the interior lights on top are part of the drop. This is an old time type of backdrop that depicts like a French street in late 1800 to early 1900 why there is a interior ceiling with lights on the top of this backdrop is in my opinion stupid. Also the seams should have been glued in a downward overlay application. Instead they are in a upward application which makes the top of the seam fold down exposing the white backside of the drop. Avoid. And by something that is actually cloth and not vinyl.
This is my first DIY project. I decided to make this backdrop stand so when I film my YouTube videos. I bought all of the products used from my local Home Depot. I bought three 10 feet long PCV pipes. 4 end caps, 4 T-caps and 2 Elbow Caps. I had a Home Depot Employee cut the PCV pipe for me in store. The 1st PCV was cut in TWO 54 inch long pieces. The 2nd PCV pipe was cut into FOUR 30 inch long pieces. The 3rd PCV pipe was cut into FOUR 12 inch long pieces. I got this idea from Pinterest and I found it very helpful. I spent $10.23 total, including tax, and it took me less than 10 minutes to construct this project. This is great for Vlogging, low-budget photography studios or even a photo-booth at an or birthday party!
The backdrop support system typically mounts backdrops that feature a pole pocket. This pocket simply slides onto the cross bars. Backdrops without a pole pocket can also be mounted to the backdrop support system with spring clamps. Spring clamps (AKA A-Clamps) can be found at any hardware store and typically only cost a few dollars. These clamps are great to have around your studio, as they also allow you to clamp backdrops taut at the bottom to eliminate wrinkles or shadows.
I am helping a friend’s daughter with her wedding planning and want to make a backdrop like this for the wedding ceremony. Can you elaborate on how the strings of lights were plugged in and whether they all “hung” versus the string light hanging down and then looping back up, if that makes sense? I like the look of them just hanging but it seems like plugging a bunch of individual ones would be hard. Am I making this too complicated?!
This was my first order with this product and I like it. The only thing that threw me off is that I expected it to be as pictured. Brick all as the 9x6 and the extra white on the bottom. It is in fact 9x6. I have included a couple test shots. The product works as expected. I love white back grounds. I think that this adds just a little bit of texture to them. Also important to not be right up against the backdrop. make sure that you get some distant between the subject and the back drop.
I needed a small kit that I would be ablt to take with me to anywhere i needed some extra lighting or a backdrop. This kit looked compact and had the essentials as well. I'm actually surprised at how much I've done using this kit, ive done amateur and commercial photography using this kit (mostly the lighting as supplemental). It works great for on the go projects and the case it all comes in is well made and easy to carry.
A 5 or 6-foot wide backdrop is a great size for headshots and ¾-length portraits. These backdrops are easy to manage and still only requires minimal space to set up. These backgrounds are ideal for event photographers who often work in busy spaces or for photographers working in a small home studio. While 5 to 6-foot backdrops offer more flexibility than 3.5-foot backdrops, they still become a bit tight if when photographing a couple or full-length portrait.
Stock up on extra drive components such as chains, switches, and weights, so you can quickly replace broken or missing parts. Be sure to keep plenty of spare clips, hooks, and brackets on hand so portrait backgrounds and video backdrops stay in place during shoots. Maintain clean and organized work spaces by storing paper rolls and mounting poles on wall-mounted and freestanding storage racks.